TQC0015 high isolation, absorptive spdt switch applications ? cellular infrastructure ? test and measurement ? smart energy ? uhf/vhf ? lmr ? general pur pose broadband wireless ? enable pin functionality 16- pin 4 ? x ? 4 ? mm qfn package ordering information part no. description TQC0015 spdt absorptive switch TQC0015 - pcb 100 ? ? ? 45 00 m hz evaluation board standard t/r size = 2500 pieces on a 13 ? reel f unctional block diagram 7 8 6 5 14 13 15 16 1 2 3 4 v ctrl rfc nc v dd gnd gnd rf1 rf2 nc nc nc nc v en nc nc nc backside paddle - rf/dc gnd pin 1 reference mark 12 11 10 9 controller product features ? low insertion loss ? +56 ? dbm input ip3 ? high isolation ? absorptive ? + 1.8 ? v logic compatible ? termination ?off? state functionality for output ports ? single positive voltage control ? 4 ? x ? 4 ? mm 16 - pin qfn package p in configuration pin no. symbol 1 v dd 2 v ctrl 3 rfc 4 , 6 ? ? ? ? general description the TQC0015 is a gaas fet single - pole, double throw (spdt) high isolation absorptive s witch that provides 100 ? ? ? 60 00 mhz broadband performance. the TQC0015 may be operated using a dc supply ranging from + 3 to + 5 volts and with control signals compliant to + 1.8 cmos logic . the switch has an added functionality with a disable pin where both output ports are terminated in 50 ohms. the TQC0015 is packaged in a rohs - compliant, compact 4 ? x ? 4 mm surface - mount leadless package. this spdt switch is targeted for use in wireless infrastructure, test and measurement, or can be used for any general pu rpose wireless application. data sheet rev . h 0 9 - 17- 14 - 1 of 7 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com
TQC0015 high isolation, absorptive spdt switch recommended operating conditions parameter min typ m ax units v dd +3.0 +3.3 +5.5 v v ctrl +1.8 v dd v operating temp. range ?40 absolute maximum ratings parameter rating storage temperature ? +165? , cw, 50, +33?dbm ? ? +?0.5?v operation of this device outside the parameter ranges given above may cause permanent damage. switch control truth table signal path state rfc to rf2 low low off (isolation) on (insertion loss) low high on (insertion loss) off (isolation) high low off ( terminated ) off ( terminated ) high high off ( terminated) off ( terminated ) digital control voltages state bias condition low + 0. 45 v high +1.4 v electrical specifications test conditions unless otherwise noted: v dd ? = ? +3.3 ? v, v ctrl ? = ? +1.8 ? v, temp. ? = ? +25 ? c, 50 system parameter conditions min typ max units operational frequency range 100 6000 mhz control voltage l ow 0 + 0.5 v high + 1. 2 v dd v insertion loss 0.1 ? ? ? 1.0 ghz 1 .0? ? ?2.6 ghz 2. 6? ? ? 3.0 ghz 3.0 ? ? ? 4.5 ghz 0.5 0.7 0. 8 0.9 0.8 1.0 db isolation ? rfc to rf1/rf2 0.1 ? ? ? 1.0 ghz 1 . 0? ? ?2 . 6 ghz 2. 6? ? ? 3.0 ghz 3.0 ? ? ? 4.5 ghz 45 38 52 43 42 40 db isolation ? rf1 to rf2 0.1 ? ? ? 1.0 ghz 1 . 0? ? ?2 . 6 ghz 2. 6? ? ? 3.0 ghz 3.0 ? ? ? 4.5 ghz 45 35 50 42 41 38 db return loss ? rfc port 0.1 ? ? ? ? ?2.6 ghz 2.6? ? f = 2 ghz +34 dbm input ip3 f = 2 ghz, pin/tone=+ 15 dbm, f=1 m data sheet rev . h 0 9 - 17- 14 - 2 of 7 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com
TQC0015 high isolation, absorptive spdt switch TQC0015 - pcb evaluation board j6 j4 u1 c1 c2 c3 c4 r1 c5 c6 j5 j9 c7 j2 rf output 2 j4 v dd j1 rf input backside paddle c2 c4 c3 j3 rf output 1 c1 r1 j5 v ctrl j6 gnd j7 rf input c6 j8 rf output c5 pcb loss calibration line u1 c7 7 8 6 5 14 13 15 16 1 2 3 4 v ctrl rfc nc v dd gnd gnd rf1 rf2 nc nc nc nc v en nc nc nc 12 11 10 9 controller j9 triquint pcb 1 084809 material and stack - up 1 oz. cu bottom layer nelco n-4000-13 core nelco n-4000-13 r =3.7 typ. 1 oz. cu top layer 1 oz. cu inner layer 1 oz. cu inner layer 0.014" 0.014" 0.062" 0.006" finished board thickness 50 ohm line dimensions: wi dth = .021? spacing = .006 ? bill of material ? TQC0015 - pcb reference des. value description manuf. part number n n printe ircuit oar riuint re. n pd itc riuint ? ?c6 0 jumper, 0402 various j4, j5, j6 , j9 n/a solder turret mill max 2533- 0 - 00- 44- 00- 00- 07 - 0 j1, j2, j3, j7, j8 n/a conn, rf, sma f strt, .062 pcb radiall inc. 9602 - 1111 - 018 data sheet rev . h 0 9 - 17- 14 - 3 of 7 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com
TQC0015 high isolation, absorptive spdt switch typica l performance ? TQC0015 - pcb test conditions unless otherwise noted: v dd = + 3.3 v , v ctrl = + 1.8 v , v en = 0 v , temp= 25 c , 50 system parameter typical value units frequency 1 2 3 g hz insertion loss (1) 0. 5 0.6 0.7 db rfc port return loss 20 20 1 6 db rfc to rf1/rf2 isolation 5 2 46 4 3 db rfc to rf1/rf2 isolation (disabled) 49 43 40 db rf1 to rf2 isolation 50 4 4 4 1 db input p1db +3 6 + 3 4 + 2 8 dbm input ip3 (2) +5 6 + 56 + 56 dbm notes: 1. values are insertion loss from device input pin to device output pin. eval board rf i/o line losses have been subtracted . 2. iip3 measured with two tones at an input power of +15 ? dbm / tone separated by 1 ? mhz. performance plots ? TQC0015 - pcb test conditions unless otherwise noted: v dd ? ? ? ? ? ? ? ? ? ? 50? system ?40 -30 -20 -10 0 0 1000 2000 3000 4000 5000 6000 |s22| (db) frequency (mhz) rf1 return loss vs. frequency +85 c +25 c ?40 c +85 c +25 c ?40 c disabled enabled -30 -20 -10 0 0 1000 2000 3000 4000 5000 6000 |s22| (db) frequency (mhz) rf2 return loss vs. frequency +85 c +25 c ?40 c +85 c +25 c ?40 c disabled enabled -4 -3 -2 -1 0 0 1000 2000 3000 4000 5000 6000 |s21| (db) frequency (mhz) insertion loss vs. frequency +85 c +25 c ?40 c -70 -60 -50 -40 -30 -20 0 1000 2000 3000 4000 5000 6000 |s21| (db) frequency (mhz) rfc to rf1/rf2 isolation vs. frequency +85 c +25 c ?40 c +85 c +25 c ?40 c disabled enabled -70 -60 -50 -40 -30 -20 0 1000 2000 3000 4000 5000 6000 |s21| (db) frequency (mhz) rf1 to rf2 isolation vs. frequency +85 c +25 c ?40 c +85 c +25 c ?40 c disabled enabled 50 52 54 56 58 60 1 1.5 2 2.5 3 iip3 (dbm) frequency (ghz) input ip3 vs. temperature +85 c +25 c ?40 c rfc to rf2 26 28 30 32 34 36 38 1 1.5 2 2.5 3 p1db (dbm) frequency (ghz) input p1db vs. frequency +85 c +25 c ?40 c rfc to rf1 33 34 35 36 37 38 1 1.5 2 2.5 3 p1db (dbm) frequency (ghz) input p1db vs. frequency +85 c +25 c ?40 c rfc to rf2 data sheet rev . h 0 9 - 17- 14 - 4 of 7 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com
TQC0015 high isolation, absorptive spdt switch switching speed switching speed measuremen t based on tqs application board using shutdown circuit: v ctrl ? = ? + 1.8 ? v, v en ? = ? 0 ? v, v dd ? = ? + 3.3 ? v with c1, c2, c3 = 100?pf ? ? l? ? 46? l? ? 132? with c1, c2, c3 = 10?pf ? l? ? l? ? pin configuration and description 7 8 6 5 14 13 15 16 1 2 3 4 v ctrl rfc nc v dd gnd gnd rf1 rf2 nc nc nc nc v en nc nc nc backside paddle - rf/dc gnd pin 1 reference mark 12 11 10 9 controller pin no. label description 4 , 6 ? ? ? ? - 5 of 7 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com
TQC0015 high isolation, absorptive spdt switch package marking and dimensions gnd/thermal pad .10 c .08 c seating plane 16x 2.500.05 exp. dap 16x 0.400.05 2.500.05 exp. dap .8500.050 c 16x 0.300.05 16x 0.65 pitch pin #1 identifier chamfer 0.300 x 45 terminal #1 identifier 0.000 0.050 .203 ref. 1.95 ref. 4.0000.050 4.0000.050 n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. except where noted, this part outline conforms to jedec stan dard mo - 220, issue e (variation vggc) for thermally enhanced plastic very thin fine pitch quad flat no lead package (qfn). 3. dimension and tolerance formats conform to asme y14.4m - 1994. 4. the terminal #1 identifier and terminal numbering conform to jesd 95 -1 s pp- 012 5. contact plating: nipdau pcb mounting pattern e de e e n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10?). 4. ensure good package backside paddle solder attach for reliable operation a nd best electrical performance. 0015 yyww xxxx xx package marking product identifier: 0015 date code: yyww assembly code: xxxx xx data sheet rev . h 0 9 - 17- 14 - 6 of 7 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com
TQC0015 high isolation, absorptive spdt switch product compliance information esd sensitivity ratings caution! e sd - sensitive device esd rating: class 0b value: 1 25 v to < 250 v test: human body model (hbm) standard: jedec standard js - 001 - 2012 esd rating: class c3 value: 1000 v test: charged device model (cdm) standard: jedec standard jesd22 - c101 solderability comp atible with both lead - free (260 ? c max. reflow temperature) and tin/lead (245 ? c max. reflow temperature) soldering processes. package contact plating: nipdau rohs compliance this part is compliant with eu 2002/95/ec rohs directive ( restrictions on the use of certain hazardous substances in electrical and electronic equipment). this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free msl rating msl rating : level 1 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 important notice for the latest specifications, additional product information, worldwide sales and distribution locations, and information abo ut triquint: web: www.triquint.com tel: +1.503.615.9000 email: info - sales@triquint.com fax: +1.503.615.8902 for technical questions and application information: email: sjcapplications.engineering@triquint.com contact information he information contained herein is believed to be reliable. triquint makes no warranties regarding the informati on contained herein. triquint assumes no responsibility or liability whatsoever for any of the information contained herein. triquint assumes no responsibility or liability whatsoever for the use of the information contained herein. the information cont ained herein is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change without notice. customers should obtain and verify the l atest relevant information before placing orders for triquint products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. triquint products are not warranted or authorized for use as critical components in medical, life - saving, or life - sustaining applications, or other applicat ions where a failure would reasonably be expected to cause severe personal injury or death. data sheet rev . h 0 9 - 17- 14 - 7 of 7 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com
|
